SELF TAPPING THREAD INSERTS
SLOTTED SERIES
MATERIAL AVAILABLE:
STEEL, STAINLESS STEEL 303 (A1), STAINLESS STEEL 316 (A4 / 18-10), BRASS C3604
SURFACE FINSIH AVAILABLE:
CR3 WHITE/YELLOW ZINC PLATED
CHARACTERISTICS:
1.EASY TO INSTALLED.
2.DESIGNED TO REPLACE SPRING COIL.
3.PROVIDE STRONG THREADS FOR WEAK MATERIAL LIKE ALUMINUM OR PLASTIC.
4.ABLE TO INSTALL FOR VIBRATING ENVIRONMENT.
APPICATIONS:
1.CAN BE APPLIED TO DIFFERENT MATERIAL SUCH AS PLASTIC, ALUMINUM, CAST IRON.
2.DESIGNED TO APPLY IN WEAK MATERIAL WHERE THREADS ARE FRENQUENTLY USED.
★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST
SELF TAPPING THREAD INSERTS - SLOTTED SERIES
topscrew1975 發表在 痞客邦 留言(0) 人氣()
SELF TAPPING THREADED INSERT
MANUAL INSTALLATION TOOLS
I. HOLE SIZE:
RECOMMENDED HOLE SIZE IS INDICATED ON EACH DATA SHEET AND IS INTENDED TO BE FOR REFERENCE ONLY. HOLE SIZE MAY NEED TO BE INCREASED OR DECREASED DEPENDING ON BASE MATERIAL, INSTALLATION TORQUE OR PERFORMANCE REQUIRED. OPTIMUM HOLE SIZE SHOULD BE DETERMINED BY REQUESTING SAMPLES & INSTALLING THEM IN THE INTENDED MATERIAL.
II. HOLE DEPTH:
IN THRU HOLE APPLICATIONS THE INSERT LENGTH SHOULD NOT EXCEED THE MATERIAL THICKNESS. IN BLIND HOLE APPLICATIONS THE HOLE DEPTH SHOULD BE 1.2XINSERT LENGTH AND THIS VALUE IS INDICATED ON MOST DATA SHEETS.
III. COUNTERSINK
A 60°COUNTERSINK IS REQUIRED FOR MOST MATERIALS TO INSURE A FLUSH SURFACE AFTER INSTALLATION.
IV. WALL THICKNESS
WALL THICKNESS SHOULD BE 0.35 TO 0.5 X HOLE DIAMETER DEPENDING ON BASE MATERIAL.
★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST
topscrew1975 發表在 痞客邦 留言(0) 人氣()
LOKSERT-TOOL
topscrew1975 發表在 痞客邦 留言(0) 人氣()
LOKSERT-STANLESS
High strengt and reliability provides maximum pullout strength.
Installed using standard drills and taps.
Simple installation - no special skills required.
Suitable for use in a wide range of parent materials.
Impossible to cross thread during installation.
Simple removal process if required.
No tang to break and remove.
Available in metric sizes, inch sizes and spark plug sizes.
Available in Thinwall and Heavy Duty.
Material: Steel/ Stainless Steel
topscrew1975 發表在 痞客邦 留言(0) 人氣()
LOKSERT-STEEL
Solid bushing utilising locking keys provides positive mechanical lock against rotation.
High strengt and reliability provides maximum pullout strength.
Installed using standard drills and taps.
Simple installation - no special skills required.
Suitable for use in a wide range of parent materials.
Impossible to cross thread during installation.
Simple removal process if required.
No tang to break and remove.
Available in metric sizes, inch sizes and spark plug sizes.
Available in Thinwall and Heavy Duty.
Material: Steel/ Stainless Steel
topscrew1975 發表在 痞客邦 留言(0) 人氣()
SPEED PIN RIVET / DRIVE PIN RIVETMATERIAL AVAILABLE FOR SPEED PIN RIVET (DRIVE PIN RIVET):
BODY: ALUMINUM 2117 / STAINLESS STEEL 302 (INOX A2/18-8) / STEEL 1006
PIN: ALUMINUM 2024 / STAINLESS STEEL 304 (INOX A2/18-8) / STEEL 1022
FINISH SURFACE AVAILABLE FOR SPEED PIN RIVET (DRIVE PIN RIVET):
PLATING: CR3 WHITE ZINC PLATED/ CR3 YELLOW ZINC PLATED/ CR3 BLACK ZINC PLATED/ ANODIZED/CLEAN
ADVANTAGES OF SPEED PIN RIVET (DRIVE PIN RIVET):
1.SPEED PIN RIVET IS FAST AND EASY TO INSTALL.
2.NO SPECIAL INSTALLATION TOOL IS REQUIRED FOR SPEED PIN RIVET, JUST A HAMMER WILL DO.
3.VARIOUS MATERIALS ARE AVAILABLE FOR SPEED PIN RIVET.
4.VARIOUS HEAD STYLES ARE AVAILABLE FOR SPEED PIN RIVET.
5.SPEED PIN RIVET WILL NOT DAMAGE THE APPLICATION SURFACE
6.SPEED PIN RIVET CAN BE RUST RESISTANT.
7.SPEED PIN RIVET CAN BE APPLIED TO WIDE THICKNESS.
8.THE APPEARANCE LOOKS GOOD AFTER INSTALLATION.
★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST
★Available Size:5/32"、5/16"、3/16"、3/8"、1/8"、1/4"、
topscrew1975 發表在 痞客邦 留言(0) 人氣()
MALE FEMALE RIVET
MATERIAL: ALUMINUM 5052 BRASS 2600 STAINLESS STEEL 302 / 410
APPLICATION : TABLEWARE
★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST
topscrew1975 發表在 痞客邦 留言(0) 人氣()
STAINLESS STEEL / STEEL BLIND RIVET
TS.SSAS SERIES
MATERIAL AVALIABLE:
RIVET: STAINLESS STEEL 302/ 316 (INOX A2/ A4/ 18-8/ 18-10)
SHAFT: STEEL 1018~1022
FINISH SURFACE AVALIABLE:
RIVET: SELF COULOURED
SHAFT: CR3 WHITE ZINC PLATED/ CR3 YELLOW ZINC PLATED
ADVANTAGES OF SS-S BLIND RIVET:
1.PROVIDE STRONG HOLDING FOR APPLICATION.
2.LOW IN COST COMPARE WITH BOLT AND NUT.
3.IDEAL FOR WIDE RANGE APPLICATION.
4.AVAILABLE IN DOME, COUNTERSUNK OR LARGE FLANGE STYLE.
5.FAST AND EASY TO INSTALL.
6.PROVIDE HIGH TENSILE AND SHEAR STRENGTH COMPARE WITH ALUMINUM OR STEEL.
7.IDEAL FOR RUST RESISTANCE APPLICATION.
★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST
topscrew1975 發表在 痞客邦 留言(0) 人氣()
ALL STAINLESS STEEL BLIND RIVET
TS.SSASS SERIES
MATERIAL AVALIABLE:
RIVET: STAINLESS STEEL 302/ 316 (INOX A2/ A4/ 18-8/ 18-10)
SHAFT: STAINLESS STEEL 302/ 316 (INOX A2/ A4/ 18-8/ 18-10)
FINISH SURFACE AVALIABLE:
RIVET: SELF COULOURED
SHAFT: SELF COULOURED
ADVANTAGES OF SS-S BLIND RIVET:
1.PROVIDE STRONG HOLDING FOR APPLICATION.
2.LOW IN COST COMPARE WITH BOLT AND NUT.
3.IDEAL FOR WIDE RANGE APPLICATION.
4.AVAILABLE IN DOME, COUNTERSUNK OR LARGE FLANGE STYLE.
5.FAST AND EASY TO INSTALL.
6.PROVIDE HIGH TENSILE AND SHEAR STRENGTH COMPARE WITH ALUMINUM OR STEEL.
7.IDEAL FOR RUST RESISTANCE APPLICATION.
★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST
topscrew1975 發表在 痞客邦 留言(0) 人氣()
ALL STEEL BLIND RIVET
TS.SAS. SERIES
MATERIAL AVALIABLE:
RIVET: STEEL 1006
SHAFT: STEEL 1018~1022
FINISH SURFACE AVALIABLE:
PLATING: CR3 WHITE/ YELLOW/ BLACK ZINC PLATED/ CR3 ZINC NICKEL PLATED...ETC
COLOURED: YELLOW/ RED/ BLACK/ WHITE...ETC.
ADVANTAGES OF S-S BLIND RIVET:
1.PROVIDE STRONG HOLDING FOR APPLICATION.
2.LOW IN COST COMPARE WITH BOLT AND NUT.
3.IDEAL FOR WIDE RANGE APPLICATION.
4.AVAILABLE IN DOME, COUNTERSUNK OR LARGE FLANGE STYLE.
5.FAST AND EASY TO INSTALL.
6.PROVIDE HIGH TENSILE AND SHEAR STRENGTH COMPARE WITH ALUMINUM.
7.IDEAL FOR RUST RESISTANCE APPLICATION.
★ OTHER SIZE, MATERIAL ARE AVAILABLE UPON REQUEST
topscrew1975 發表在 痞客邦 留言(0) 人氣()
Company Profile (2)
